1. Sorry for the initial hiccups after launch. Everyone should be able to login now.

    Welcome to the new Pavement Sucks!

    If you are having a problem logging in, try RESETTING YOUR PASSWORD HERE

cat c15 tool help

Discussion in 'The Brothel' started by mudpuppy, Sep 28, 2008.


  1. mudpuppy

    mudpuppy
    Expand Collapse
    New Member

    1,135
    0
    0
    I'm looking for part numbers for the front and rear seal installers and I cant find anything. I found some older installers but not sure if they will work
     

  2. Chubacabra

    Chubacabra
    Expand Collapse
    New Member

    166
    0
    0
    Did you check on cats sis program for the correct tool number?
     

  3. mudpuppy

    mudpuppy
    Expand Collapse
    New Member

    1,135
    0
    0
    I don't know what that program is
     
  4. Chubacabra

    Chubacabra
    Expand Collapse
    New Member

    166
    0
    0
    Caterpillar sis program is the get all know all info about anything related to cat. Here I'll try to look up on sis and give you the right part number or diagram. By the way what kinda truck you workin on?
     
  5. Chubacabra

    Chubacabra
    Expand Collapse
    New Member

    166
    0
    0
    Disassembly and Assembly

    C15 On-highway Engines Media Number -RENR9403-10 Publication Date -01/07/2008 Date Updated -16/07/2008





    i03207701





    Crankshaft Rear Seal - Install

    SMCS - 1161-012







    Installation Procedure

    Table 1 Required Tools

    Tool Part Number Part Description Qty

    D 5P-1733 Seal Locator 1

    5P-1737 Bolt 3

    9S-8858 Nut (Seal Installer) 1

    6V-6143 Seal Installer 1









    --------------------------------------------------------------------------------









    Disassembly and Assembly

    C15 On-highway Engines Media Number -RENR9403-10 Publication Date -01/07/2008 Date Updated -16/07/2008





    i03203779





    Crankshaft Front Seal - Install

    SMCS - 1160-012







    Installation Procedure

    Table 1 Required Tools

    Tool Part Number Part Description Qty

    D 5P-1733 Seal Locator 1

    E 5P-1737 Bolt 3

    F 9S-8858 Nut (Seal Installer) 1

    G 6V-6142 Seal Installer 1









    --------------------------------------------------------------------------------



    NOTICE

    Keep all parts clean from contaminants.



    Contaminants may cause rapid wear and shortened component life.





    --------------------------------------------------------------------------------





    Note: The crankshaft front seal and the wear sleeve must be replaced at the same time. Once the crankshaft front seal and the wear sleeve are separated, these components cannot be used again.



    Note: Do not use any type of lubricant during the installation of the crankshaft front seal and the wear sleeve.





    Before installation of the crankshaft front seal and the wear sleeve, inspect the crankshaft for scratches. Also, inspect the crankshaft for any distortion on the surface that may lead to an out of round condition. Use a polishing cloth in order to remove any imperfections on the crankshaft.



    Clean the outside diameter of the crankshaft.



    --------------------------------------------------------------------------------



    View Image









    --------------------------------------------------------------------------------



    Illustration 1 g01635160







    Fasten Tooling (D) to the crankshaft with Tooling (E) .

    Note: Install the crankshaft front seal with the arrow that shows the direction of crankshaft rotation toward the front of the engine.





    Position wear sleeve (2) and crankshaft front seal (1) on Tooling (D) . Install Tooling (G) on Tooling (D) . Lubricate the face of the washer on Tooling (F) . Install Tooling (F) on Tooling (D) .



    Tighten Tooling (F) until Tooling (G) contacts Tooling (D) .



    Remove Tooling (F) and Tooling (G) from Tooling (D) .



    Remove Tooling (E) and Tooling (D) from the crankshaft.

    End By: Install the vibration damper and the pulley. Refer to Disassembly and Assembly, "Vibration Damper and Pulley - Remove and Install".











    --------------------------------------------------------------------------------



    Copyright 1993 - 2008 Caterpillar Inc.

    All Rights Reserved.

    Private Network For SIS Licensees.

    Tue Sep 30 01:50:39 EDT 2008







    NOTICE

    Keep all parts clean from contaminants.



    Contaminants may cause rapid wear and shortened component life.





    --------------------------------------------------------------------------------





    Note: The crankshaft rear seal and the wear sleeve must be replaced at the same time. Once the crankshaft rear seal and the wear sleeve are separated, these components cannot be used again.





    --------------------------------------------------------------------------------



    View Image









    --------------------------------------------------------------------------------



    Illustration 1 g01636744





    Note: Do not use any type of lubricant during the installation of the crankshaft rear seal and wear sleeve.





    Before installation of the crankshaft rear seal and the wear sleeve, inspect the crankshaft for scratches. Also, inspect the crankshaft for any distortion on the surface that may lead to an out of round condition. Use a polishing cloth in order to remove any imperfections on the crankshaft.



    Clean the outside diameter of the crankshaft and the inside diameter of the wear sleeve.

    Note: Install the crankshaft rear seal with the arrow that shows the direction of crankshaft rotation toward the rear of the engine.





    Use Tooling (D) to install wear sleeve (2) and crankshaft rear seal (1) .

    End By: Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".











    --------------------------------------------------------------------------------
     
  6. mudpuppy

    mudpuppy
    Expand Collapse
    New Member

    1,135
    0
    0
    at my work we don't do in depth motor work. a buddy of mine that I work with does on the side I'm helping him find some specialty tools. and I'm going to give him a hand so that I can get more experience on internal motor work. I really appreciate the help
     

Share This Page